Test Online Free HP HPE0-V14 Exam Questions and Answers
The questions for HPE0-V14 were last updated On May.12 2023 Get HPE0-V14 Full AccessQuestion No : 1
Read the question, and then refer to the exhibit.
<Switch-A>display interface Ten-GigabitEthernet 1/0/1 Ten-GigabitEthernet1/0/1 Current state: Administratively DOWN Line protocol state: DOWN IP packet frame type: Ethernet II, hardware address: d894-03fb-793d Description: Ten-GigabitEthernet1/0/1 Interface Bandwidth: 10000000 kbps Loopback is not set Media type is stack wire, port hardware type is STACK_SFP_PLUS Unknown-speed mode, unknown-duplex mode Link speed type is autonegotiation, link duplex type is autonegotiation Flow-control is not enabled Maximum frame length: 10000 Allow jumbo frames to pass Broadcast max-ratio: 100% Multicast max-ratio: 100% Unicast max-ratio: 100% PVID: 1 MDI type: Automdix Port link-type: Trunk VLAN Passing: 10, 20 VLAN permitted: 10, 20 Trunk port encapsulation: IEEE 802.1q Port priority: 0 Last link flapping: 0 hours 0 minutes 18 seconds Last clearing of counters: Never Peak input rate: 78 bytes/sec, at 2011-03-31 04:55:57 Peak output rate: 15 bytes/sec, at 2011-03-30 23:00:57 Last 300 second input: 0 packets/sec 67 bytes/sec - % Last 300 second output: 0 packets/sec 14 bytes/sec - % Input (total): 62670 packets, 8565340 bytes 0 unicasts, 0 broadcasts, 62670 multicasts, 0 pauses Input (normal): 62670 packets, - bytes 0 unicasts, 0 broadcasts, 62670 multicasts, 0 pauses Input: 0 input errors, 0 runts, 0 giants, 0 throttles 0 CRC, 0 frame, - overruns, 0 aborts C ignored, - parity errors Output (total): 3707 packets, 1294835 bytes 0 unicasts, 0 broadcasts, 3707 multicasts, 0 pauses Output (normal): 3707 packets, - bytes 0 unicasts, 0 broadcasts, 3707 multicasts, 0 pauses Output: 0 output errors, - underruns, - buffer failures 0 aborts, 0 deferred, 0 collisions, 0 late collisions 0 lost carrier, - no carrier
A customer added a new switch to their network. They connected it using interface Ten-GigabitEthernet 1/0/1. They are using VLAN 10 and 20 for the devices in their network.
The new switch was fully operational. Then, the customer experienced a power failure later that day and could not reach any device on the new switch after the power returned.
From the output in the exhibit, would could be the issue?
Answer:
Explanation:
Reference: https://assets.ext.hpe.com/is/content/hpedam/a00004216enw
Question No : 2
DRAG DROP
A customer needs a new VMware environment for a critical stock trading application and will need high performance compute and low latency storage.
Identify the correct component configurations on the left and drag them to the answer area on the right. (Choose two.)
Answer:
Explanation:
ANS - Xeon-platinum, af20
https://ark.intel.com/content/www/us/en/ark/compare.html?productIds=123546,192482
Question No : 3
A security client needs a surveillance solution to support 239 Cameras. They expect to generate 2PB of data and require a 10Gb network infrastructure in a single rack.
Which solution should you recommend to meet the customer requirements?
Answer:
Explanation:
Reference: https://h20195.www2.hpe.com/v2/GetPDF.aspx/4AA0-6064ENW.pdf
Question No : 4
What should you configure to limit the scope of broadcast domains in an Ethernet network?
Answer:
Explanation:
Reference: https://assets.ext.hpe.com/is/content/hpedam/documents/a00069000-9999/a00069468/a00069468enw.pdf
Question No : 5
DRAG DROP
Match each HPE solution to its corresponding technology usage.
Answer:
Question No : 6
A customer with limited IT administration resources needs a complete HPE server, storage, and networking solution. The solution must be able to be deployed in an hour or less through a simple, wizard-based setup. They want to manage the HPE solution through a simple, integrated plug-in to vCenter, since their IT staff members are already familiar with vCenter.
Which HPE solution best meets the customer requirements?
Answer:
Question No : 7
1.A customer has requested that you provide them with an architecture and bill-of-materials for a stack of top-of- rack switches. The customer has 34 HPE DL360 servers in the rack, each with four 1GBASE-T Ethernet ports which need to be connected to the network.
The customer is upgrading 50% of the 1GBASE-T Ethernet ports on the servers to 10GBASE-T Ethernet ports and needs the switching to support the upgraded servers. They are opposed to a chassis switch, and want to keep the number of managed devices on the network to a minimum.
Which architecture meets the customer requirements?
Answer:
Explanation:
Needs 4 switches for port count, customer wants minimum of managed devices so one stack, VSX only supports two switches so must be an IRF based stack. As to ShaunSong's comment, 10GBaseT ports also negotiate 1000BaseT so are inherently 1/10Gb capable.
Question No : 8
DRAG DROP
Place the components on the left in the correct order on the right for the recommended power-up sequence.
Answer:
Explanation:
✑ SAN switches
✑ Tape libraries
✑ Disk storage
✑ Host servers
Question No : 9
You are designing a server solution that requires a significant amount of memory.
Which guideline should you keep in mind when working with memory channels?
Answer:
Question No : 10
You are installing a data center switch.
Which methods are recommended to configure the switch? (Choose two.)
Answer:
- TOP 50 Exam Questions
-
Exam
All copyrights reserved 2024 PassQuestion NETWORK CO.,LIMITED. All Rights Reserved.
Passquestion doesn't offer Real Microsoft, Amazon, Cisco Exam Questions. All Passquestion content is sourced from the Internet.