Question No : 1
Refer to the exhibit.



The command show LLDP neighbor-info gets typed into Access-1. All switches are Aruba OS-CX switches.
What is the output of this command?

• A.Option A
• B.Option B
• C.Option C
• D.Option D

Show Answers

Answer:

Question No : 2
Refer to the exhibit.






What command will display the debug l2mac events?

• A.show module L2MAC
• B.show debug terminal
• C.show debug buffer module L2MAC
• D.show debug all

Show Answers

Answer:

Question No : 3
What is an available command on an Aruba AOS-CX switch that would back up the secondary image to a secure remote repository?

• A.backup secondary sftp://[email protected]/G
• B.10.04.0003.swi
• C.copy secondary sftp://[email protected]/G
• D.10.04.0003.swi
• E.copy sftp://[email protected]/G
• F.10.04.0003.swi secondary
• G.copy secondary tftp://[email protected]/G
• H.10.04.0003.swi

Show Answers

Answer:

Question No : 4
Core# configure terminal
Core(config)# vrf Green
Core(config-vrf)# exit
Core(config)#
Core(config)# interface vlan 50
Core(config-if-vlan)# ?
Given the configuration on the CORE switch shown above, what command would follow to assign the switched virtual interface (SVI) vlan 50 to the VRF created?

• A.Core(config-if-vlan)# vrf attach Green
• B.Core(config-if-vlan)# ip vpn-instance Green
• C.Core(config-if-vlan)# ip vrf forwarding Green
• D.Core(config-if-vlan)# routing-context Green vrf

Show Answers

Answer:

Question No : 5
What is the process where a compute device converts logical data bits into the correct physical representation depending on the media?

• A.Demodulation
• B.Modulation
• C.Propagation
• D.Encapsulation

Show Answers

Answer:

Question No : 6
Refer to the exhibit.



The above output is the result of issuing the command show system resource-utilization.
What command should be used to enable terminal output line by line or page by page?

• A.The command page
• B.The command terminal length 30
• C.The command more
• D.The command less

Show Answers

Answer:

Question No : 7
The following command is issued:
Switch# checkpoint rollback start
What is the result?

• A.The command will fail because rollback commands must be issued from global-config mode.
• B.The switch will revert the running-configuration to the checkpoint called 'start1 without a reboot.
• C.The command will fail because it is incomplete.
• D.The switch will use the checkpoint 'rollback1 as the starting configuration on next reboot.

Show Answers

Answer:

Question No : 8
Refer to the exhibit



Which command on Access-2 port 1/1/4 will enable connectivity between PC-1 and Server-1 without any routing enabled in the network?

• A.Access-2 (config-if-1/1/4)# vlan access 1, 10, 20, 255
• B.Access-2 (config-if-1/1/4)# vlan access 20
• C.Access-2 (config-if-1/1/4)# vlan 20 untag 1/1/4
• D.Access-2 (config-if-1/1/4)# vlan trunk allow 1, 10, 255

Show Answers

Answer:

Question No : 9
Refer to the exhibit.



Which command produces the above output?

• A.show interface port 1/1/10 trunk
• B.show vlan port 1/1/10
• C.show trunk port 1/1/10 extended
• D.show interface port 1/1/10 switchport

Show Answers

Answer:

Question No : 10
Which command can be used to find the serial number of an Aruba OS-CX switch?

• A.The command inventory
• B.The command version
• C.The command show running-configuration
• D.The command show system

Show Answers

Answer: